Walplast Buildwell Repair Solutions

Product Details:

BuildWell colour putty is a wall putty with added advantage of shades like Pink, Yellow, Green and Off-White, especially developed to provide smooth finish on plastered surface. It contains finest quality minerals, polymers, white cement and pigments. Since it comes in shades, no painting required for interior to attain highest economy and speed. It can also be used for application areas like basement parking lot, staircase etc. as “Final Finish”.

Features:

• Can be applied on Interior wall and ceiling
• Gives smooth and glossy finish
• Suitable for Interior
• Save 100% of painting cost
• Better adhesion with wall surface
• Ease of use at site
• Cost-effective
• No painting required
• Aesthetic look for ceiling and interior walls
• Clean loose particles, dirt, grease and traces of foreign material from the surface, if necessary, by using sand paper or by chipping
•  For loose plaster areas, remove the defective material and re-plaster the area with BuildWell Ready-Mix Plaster.
• For ceilings/walls, which are not even, re-plaster it with BuildWell Ready-Mix plaster to make them even.
• Fill up any cracks in base plaster by using BuildWell Crack Filler.
• BuildWell Colour Putty contains only eco-friendly fillers and additives.
• However, being white cement based, it is alkaline and hence it is advisable to avoid direct eye and skin contact with this.
• In case of eye contact, flush with clean water at least for 15 minutes and seek medical help and recommend to keep it out of reach of children.

 

Product Details:

Instant Plastering BuildWell Ready-Mix Plaster is manufactured in modern dry mix plant with computerised batch process. Plaster is ready to use by just mixing water at site. This process eliminates job-site mixing practices. Hence it gives consistent quality with required sand mesh sizes in exact proportion which is most important for compactness of plaster. Further to have desired workability, less rebounding losses, required slump properties and overall durability, polymers are added in BuildWell Ready-Mix Plaster.

Features:

• Compact plaster, reduce void gaps
• Negligible silt content
• Reduces rebounding
• BuildWell Ready-Mix Plaster provides highly durable plaster that cuts repair the maintenance cost
• Excellent work ability and good adhesion on various substrate
• Paint finish and life of paint are enhanced
• The substrate needs to be cleaned and made free from grease and loose particles.
• The porous and absorbent substrates need to be pre-wetted prior to application of BuildWell Ready-Mix Plaster to prevent premature loss of water from the plaster.
• This will ensure that thin layer can be applied without cracking problems and proper cement hydration and adherence of the mortar to the substrate is attained.
• Depending upon substrate and climate add approx. 7 to 8 liters of water per 40 kg bag.
• Different grade of sand used in exact proportion ensuring compactness in plaster.
• High silt and chloride content in sand impedes adhesion properties in mortar, causing high de-bonding losses.
• Negligible silt and organic matter free plaster ensure strong adhesion and durability.
• High DE-BONDING LOSSES
• Smooth and hard surface provides aesthetic base of plaster to work upon.
• Due to practical on site mixing practice, chances of crack formation is more.
• (RMP) produced at automated dry mix plant. Chances of is very negligible subjected to proper curing and application.
• Due to presence of moisture in sand it is not possible to determine exact quantity of water to be mixed.
• Sand cement ratio is maintained as (RMP) is made in automated plant.
• Reducing of plaster is not possible.
• Can be reduced up to 25% keeping the required strength.
• Polymer modification difficult as it involves multiple polymers and doses
• Polymers already added, results in overall durability

 

Product Details:

BuildWell Block Jointing Mortar is a superior water resistant cement based mortar specially formulated for joining blocks. This mortar is specially designed and manufactured under stringent quality controls to give superior adhesive strength, higher durability and a strong bond between the blocks. This unique combination enables this mortar to be thinner, compact and versatile. It also ensures higher bond strength and durability at only 3 mm thickness compare to the conventional mortar at 12-15 mm replacing the conventional cement and sand mix mortar completely.

Features:

• Excellent bonding to the blocks/bricks
• Better levelling
• Prevent seepage and water percolation
• Pre-mixed, only water to be added
• No curing is required after application. Thus saving water
• Thinner layer guarantees to be more cost-effective
• Easy to mix and faster to apply
• Plastering can be done after 24 hrs. of application
• Time and manpower is saved
• High strength adhesion
• Lesser shrinkage and seamless structure
• Consistency of material and quality
• Can be applied by ordinary mason – no special skill required
• The surface area where BuildWell Block Jointing Mortar needs to be applied should be sound, thoroughly clean and free from dust, grease, oil and any loose material.
• The masonry surface should be pre-wetted before applying BuildWell Block Jointing Mortar
•  Line out on the concrete slab should be done by using conventional cement mortar to get the desired line level.
• Laying and joining of masonary units like AAC Blocks, Hollow Blocks, Fly ash Bricks and concrete Blocks.
• BuildWell Block Jointing Mortar contains only eco-friendly fillers and additives.
• In case of eye contact, wash with clean water for at least 15 minutes and seek for medical help if needed and recommend to keep it out of reach of children.
• Setting Time: 2 mm thick on concrete Storage 7 days in polythene bag @ 23 C + 7 days @ 23 C with 50% R.H.

Product Details:

BuildWell Gypsum Plaster is a light weight gypsum based plaster suitable for application on most internal surfaces including brick, block and concrete. It consists of superior quality gypsum, formulated with special additives to enhance working and setting characteristics, also improves workability and coverage. When dry, it provides superior whiteness, smooth and matt finish and is suitable for all internal dry plastering applications.

Product Details:

• Setting Time Initial >=30 min
• Setting Time Final <=600 min
• Setting Time 2 mm thick on concrete. Storage 7 days in polyethene bag @ 23 C + 7 days @ 23 C with 50% R.H. Not Specified
• Water Retentivity Not Specified
• Compressive Strength As per EN 998 - 12 days in mold + 5days in polyethene bag + 21 days @23 degree C with 50% R.H. for categories
• Flexural Strength Min 1.8 Mpa
• Capillary Water Absorption As per EN 998 - 1

EASYPLAST BLOCK JOINTING MORTAR is a superior water resistant Cement Based Mortar or Mortar Admixture or Mortar Cement specially formulated for joining blocks. It contains selected graded dry sand gray cement and imported polymers to improve workability, water retention durability and adhesion. It is more resistant to the corrosive environment.

As BLOCK JOINTING MORTAR contains finely graded sand it helps in laying an even strong and thin layer of joint. This is not only cost-effective but also builds even walls as this improves the leveling of walls and the plaster thickness can be reduced. This further reduces the thickness of putty application thus an all-round reduction of cost can be achieved.

Block Jointing Mortar Features

• Excellent bonding to the blocks/bricks.
• Better leveling.
• Prevent water percolation.

Block Jointing Mortar Benefits

• Saves time.
• Cost-effective.
• Can be applied by ordinary mason - no special skills required.

Block Jointing Mortar Advantages

• Good workability.
• Ease of use at the site.
• Consistent work quality.
• No curing is required.
• Plastering can be done after 24 hrs. of application.

Application Area

• Laying & Joining Of Masonry Units Like Mc Blocks, Hollow Blocks, Fly Ash Bricks, And Concrete Blocks, Etc. - Joining Of Concrete Window And Door Frames, Etc.

How to Apply

• Take The Required Quantity Of Water In A Clean Bucket, Add Easy last Block Jointing Mortar As Recommended.
• Stir Continuously For 5 -10 Minutes By Using An Electric Mixer Or By Hand To Obtain A Homogeneous Lump-Free Mix.
• Allow The Resultant Wet Mortar To Stand For About 5 Minutes For The Add Lives To Dissolve.
• Re-Mix Again For About 2 Minutes. The Mixture Is Now Ready For Application.
• Use The Mix Within 60 Minutes.
• For Best Results, It Is Advisable To Use Notch Trowel Of 3 To 4 Mm To Have Better Contact And Bonding.

Surface Preparation

• Masonry Surface Should Be Clean, Without Dust, Voids And Wet Prior To Application Of Easy last Block Jointing Mortar

Brand Walplast

Packaging Size 40 kg

Product Details:

BuildWell Coarse Putty is white cement based wall putty specially developed to be used on concrete/mortar surface wall (Internal) and ceiling to cover unevenness and pinholes on plastered surface and make the wall/ceiling white, smooth and levelled. It contains finest quality minerals, white cement and polymers and is more durable and has better adhesion strength compared to other conventional products like Gypsum and P.O.P.

Features:

• Evenness of Wall/Celling surface
• Highly Durable
• Water resistant
• Strong bonding to the base/Concrete plaster
• Excellent white & smooth finish
• Reduction in cracking
• Protects expensive paint from dampness, peeling off and flaking
• Paint finish is superior and long lasting
• Can be used on new as well as old wall/ceiling
• Reduced putty consumption
• Saves time
• Cost-effective
• Ease of use at site
• Excellent workability
• Clean loose particles, dirt, grease and traces of adhering material from the wall surface with the help of sand paper, putty blade or by wire brush.
• For loose plastered areas, remove the defective material and re-plaster the area with BuildWell Ready-Mix Plaster.
• For ceiling/wall, which is not even, re-plaster it with BuildWell Ready-Mix Plaster to make them even.
• If any cracks in base plaster, fill it by using HomeSure Crack Filler.
• Moisten the surface with sufficient quantity of clean water.
• It is very important and essential that the application area surface is pre-wet properly before the application of “BuildWell Coarse Putty”.
• The surface should be moist during application process.
• This ensures higher bonding, strength, easy workability and higher coverage within the surface.
• In areas of high temperature and low humidity, light curing is recommended for at least 2 days

 

 

Product Details:

White Cement Based Wall Putty BuildWell Wall Putty is a white cement based polymer modified wall putty specially developed as a base coat to cover unevenness and pinholes on plastered, mortar wall (Internal) and ceiling to make the surface wall white and smooth and ready for primer and paint application.

Features:

• Whitest putty
• Highly water resistant
• Strong bonding to the base plaster
• Smooth finish
• Durable & long lasting
• True colour tone of the paint is maintained
• Protects expensive paint from dampness, peeling off and flaking
• Primer is not required
• Paint finish is superior
• Excellent workability
• Avoid frequent repainting
• Reduces paint consumption
• Aesthetic look for ceiling, interior and external wall
• Ease of use at site
• Cost-effective
• Clean loose particles, dirt, grease and traces of foreign material from the surface, if necessary, by using sand paper or by chipping.
• For loose plaster areas, remove the defective material and re-plaster the area with BuildWell Ready-Mix Plaster.
• For ceilings/walls, which are not even, re-plaster it with Ready-Mix Plaster
• BuildWell Wall Putty contains only eco-friendly fillers and additives.
• In case of eye contact, flush with clean water at least for 15 minutes and seek medical help and recommended to keep it out of children reach.

Product Details:

Bonding Compound for RCC BuildWell Quick Bond is a admixture of sand, cement and superior quality polymers. It is a bonding agent that enables quick preparation of ceiling and RCC wall surface. Also offers the dual benefits of mechanical and chemical bonding, which eliminates the labor intensive hacking and reduces debonding losses.

 

Features:

• Excellent bonding
• No hacking is required on RCC wall.
• Hence prevention of micro cracking and saving of labor cost
• Strong chemical and mechanical bond
• Easy to use
• Works good for Gypsum plaster as well for cement sand plaster
• Can be easily applied by brush/roller
• Reduces hacking
• Time saving
• Less rebound loss while plastering
• It is water soluble product hence no solvent odor
• Fast drying
• Improves bonding strength between RCC wall and Plaster.
• Clean loose particle, dirt, grease and trace of foreign material from the surface.
• For good bonding on RRC, plastering should be done instantly once the BuildWell Quick Bond coat is about set completely
• Avoid inhaling the fine powder particles, wear nose mask while handling.
• Alkaline materials can seriously damage eye, therefore eye protection is strongly recommended.
• Alkaline materials are also harmful to skin therefore use of protective gloves.
• In case of eye or skin contact, flush with clean water for at least 15 mins and seek for medical help.
• Store in cool and dry location. Keep away from the reach of children.

 

 

 

Product Details:

White Cement Based Polymeric texture BuildWell Texture is a cement based Polymeric textured wall finish. It decorates the wall as well as protect both interior and exterior wall. It is more economical than other acrylic based products. Its unique pattern has distinctive appeal. Its special formulation keeps it safe against the ill-effects of the weather. It contains finest quality minerals, white cement and polymers.

Features:

• Hides cracks: It hides crack in surface undulation and refines surface cracks.
• Tough textured: Its tough textured finish lasts long and ensures low maintenance.
• Protection of plasters: It protects the plastered wall from heavy rain and wind.
• It has excellent UV resistance.
• Good workability and high durability.
• It is highly compatible with plaster and concrete wall surface.
• It has excellent resistance against the growth of algae and fungi on the wall.
• Provides best value for money.
• Remove all the loose adhering particles, growth of fungus, algae from the wall surface by wire brush and potable water.
• For loose plaster areas, remove the defective material and re-plaster the area with BuildWell Ready-Mix Plaster.
• Fill up any cracks in base plaster by using HomeSure Crack Filler.
• The surface on which the material needs to be applied should be plain and leveled.
• BuildWell Texture should not be applied to surfaces which are subjected to continuous dampness.
• Recommended: Use the material mix within 2 hours of adding water.
• BuildWell Texture coverage is approx. 4 Sq.Ft/ per kg with a thickness of 2 to 2.5 mm.